教師著作
Permanent URI for this collectionhttp://rportal.lib.ntnu.edu.tw/handle/20.500.12235/31266
Browse
Item Dye-sensitized solar cells application of Al-doped ZnO nanowires grown by low-temperature solution process(2009-12-04) Cheng, C. P.; Chen, G. W.; Ou, S. L.; Pan, J. L.Item Effect of heating temperature and magnesium content on the thermal cyclic failure behaviour of ductile irons(Maney Publishing, 2004-02-07) Cheng, C. P.; Lui, T. S.; Chen, L. H.This study elucidates the effect of residual magnesium content and heating temperature on the thermal cyclic failure behaviour of ductile irons by applying repeated heating and cooling cycles. Five irons with different residual magnesium contents ranging from 0.038 to 0.066 wt-% were obtained by controlling the amount of nodulariser additions. The thermal fatigue cracking behaviour was investigated during thermal cycling from 25蚓 to 650, 700, 750, and 800蚓, respectively. Experimental results indicate that the thermal fatigue cracking resistance of ductile iron decreases with increasing residual magnesium content. The maximum heating temperatures of 700蚓 and 750蚓 led to the most severe thermal fatigue cracking in the specimens containing 0.054 wt-% and 0.060 wt-% residual magnesium content. Recrystallisation of ferrite grain occurred when the thermal cycles exceeded a certain number after testing at 800蚓, which deferred the initiation of thermal fatigue cracking.Item Efficiency Improvement of Organic Light Emitting Diodes with Co-Deposited Hole Blocking Layer(Trans Tech Publications, 2010-04-01) Liu, C. H.; Tesng, C. H.; Cheng, C. P.There are several kinds of methods in improving the efficiency of organic light emitting diodes (OLEDs). In this work, we used a co-deposited hole blocking layer to improve the efficiency of OLEDs. The structure of the component is: ITO/ MTDATA(15 nm) /NPB(40 nm) /BCP(10 nm) /BCP: Alq(15 nm) /LiF(0.7 nm)/ Al(180 nm). We changed the mixing rate of the BCP:Alq layer to be capable of hole blocking and electron transporting, and then improved the efficiency of OLEDs. Finally, we prepared white light OLED with doping Rubrene in NPB. When the concentration of the NPB: Rubrene layer was 2.0 wt.%, the device could emit the white light at 100 mA/cm2, and the luminance was above 2300 cd/m2, and the color coordinate was x = 0.36, y = 0.37.Item Electrochromic properties and Raman spectroscopy analysis of RF sputtered tungsten oxide thin films(2009-12-04) Cheng, C. P.; Lin, S. H.; Hung, F. Y.Item EM-TuP30 Large Nonlinear Optical Properties of Lead Magnesium Niobate-Lead Titanate Thin Films Grown by Pulsed Laser Deposition(2005-10-30) Liu, D. R.; Cheng, P. T.; Ou, S. L.; Chen, J. S.; Cheng, C. P.Item Field Emission Properties of Bilayer ZnO Nanowires/Nanocrystalline Diamond Film Structures(2009-12-04) Huang, B. R.; Cheng, C. P.; Hsu, J. F.; Jou, S.; He, S. A.Item Friction stir welding of ductile iron and low carbon steel(Maney Publishing, 2010-11-01) Cheng, C. P.; Lin, H. M.; Lin, J. C.Friction stir welding (FSW) is a low distortion, high quality solid welding. There is no melting during the welding process, which results in improved welding quality. Ductile iron has the advantages of being low cost, of excellent castability, and of being good mechanically. Therefore, it is generally used in many structural engineering parts. In this study, ferritic ductile iron and low carbon steel were used to explore the qualities of dissimilar metal welding under different conditions. The FSW process, changes in the microstructure of the welding area and the mechanical properties of joints were explored. According to the research, we found that when dissimilar metal welding is conducted at 982 rev min-1 with a travelling speed of 72 mm min-1, flawless welding quality can be obtained if the stir rod rotates counterclockwise with carbon steel fixed in the advancing side and with ductile iron in the retreating side. FSW successfully provided defect free welds. However, fine pearlite and martensite structures appear in the stir zone, which result in mechanical property degradation of weldments. The stir zone in the weldments is very hard due to martensitic transformation. After heat treatment, the tensile strength improves, and the fracture site appears in the base metal of the carbon steel. However, the welding nugget is not completely filled when the stir rod directs ferritic ductile iron to the advancing side in the clockwise direction and carbon steel in the retreating side, which results in defects and lower welding quality.Item Influences of Dye Doping and Hole Blocking Layer Insertion on OLED Performance(Trans Tech Publications, 2010-04-01) Tesng, C. H.; Liu, C. H.; Cheng, C. P.This study presents the influences of dye doping and hole blocking layer insertion on the electroluminescent properties of the blue organic light emitting diode. The luminance of the device was significantly improved by BCzVB doping because of the utilization of effective F顤ster energy transfer and the improvement of carrier injection and trapping; a BCzVB dominant emission was observed. Furthermore, when a BCP layer was inserted between the TBADN:BCzVB and Alq3 layers, a thin BCP layer insertion enhanced the injection of electrons and improved the luminance of the device. In contrast, a thick BCP layer insertion caused a delay in electron transport, resulting in a decrease in current density and a deterioration in luminance.Item Optical properties of lead magnesium niobate-lead titanate thin films grown by pulsed laser deposition(2005-02-01) Liu, D. R.; Ou, S. L.; Cheng, P. T.; Cheng, C. P.Item Ultraviolet Emission of Nano-structured Zinc Oxide(2006-09-12) Lai, F. I.; Chen, W. C.; Kuo, S. Y.; Cheng, C. P.